Birm® is an efficient and economical media for the reduction of dissolved iron and manganese compounds from raw
water supplies. It may be used in either gravity fed or pressurized water treatment systems. Birm® acts as an insoluble catalyst to enhance the reaction between dissolved oxygen (D.O.) and the iron compounds. In ground waters the dissolved iron is usually in the ferrous bicarbonate state due to the excess of free carbon dioxide and is not filterable. Birm®, acting as a catalyst between the oxygen and the soluble iron compounds, enhances the oxidation reaction of Fe++ to Fe+++ and produces ferric hydroxide which precipitates and may be easily filtered. The physical characteristics of Birm® provide an excellent filter media which is easily cleaned by backwashing to remove the precipitant. Birm® is not consumed in the iron removal operation and therefore offers a tremendous economic advantage over many other iron removal methods. Other advantages of Birm® include; long material life with
relatively low attrition loss, a wide temperature performance range and extremely high removal efficiency. Negligible
labor costs are involved because Birm® does not require chemicals for regeneration, only periodic backwashing is required.
When using Birm® for iron removal, it is necessary that the water: contain no oil or hydrogen sulfide, organic matter not to exceed 4-5 ppm, the D.O. content equal at least 15% of the iron content with a pH of 6.8 or more. If the influent water has a pH of less that 6.8, neutralizing additives such as Corosex®, Calcite or soda ash may be used prior to the Birm® filter to raise the pH. Water having a low D.O. level may be pretreated by aeration.
Additions of chemicals to influent or backwash water which contacts Birm® media may inhibit iron or manganese removal or may break down or coat Birm® media. Chlorination greatly reduces Birm®'s activity. High concentrations of chlorine compounds may deplete the catalytic coating. Polyphosphates are known to coat Birm® a
nd reduce Birm®'s ability to remove iron or manganese. Before adding any chemical to the influent or backwash water, the chemical's compatibility with Birm® should be thoroughly tested.
Clack Birm® may also be used for manganese reduction with the same dependability as iron removal. In these
applications the water to be treated should have a pH of 8.0-9.0 for best results. If the water also contains iron, the pH should be below 8.5. High pH conditions may cause the formulation of colloidal iron which is very difficult to filter out. All other conditions remain the same for either manganese or iron removal.
Automatic Softeners and Filters
The pre-installed Filter Ag-Plus® is a special sediment removal media that comes with filter bed support. Its granules are known for their micro-porous, rough and irregular shapes that create a surface area over 100 times greater than filter sand. This granular structure results in a greater reduction of dirt, silt and suspended organic matter. Due to its special media structure, light weight and deep bed penetration, the solids are typically reduced down to the 5-10 micron range depending on water conditions without any rapid build-up of back pressure.
The pre-installed softener resin is a gel cation exchange resin, with exchange capacity of 32,000 grains per cubic foot, based on high salt regeneration. Quality water from fully automatic filtration and softening systems designed for residential and commercial applications. With state of the art control valves, these systems offer superior sediment loading and excellent softening capacity, resulting in longer service runs and less frequent backwash and regeneration.
Clack control valves utilize a solid-state microprocessor for single or twin (duplex) tanks to regulate all cycles of filtration, media backwash, rinsing, and regeneration. The valves allow options for backwash and regeneration frequency, and they indicate volume remaining, current flow rate, volume used (totalizer), and tank in service (in case of twin/duplex systems).
- *Service flow and backwash up to 6M3/hr (for 1” valves)
- *Front panel display
- *24 hr lithium battery backup with 8 hr carry over
- *Backwash and brining capability
- *Downflow regeneration
- *12V output AC adapter for safe installation
Clack control valves are made in the USA and are designed for residential, commercial and industrial use,they are state of the art automatic valves that cover a broad range of global applications.They are use with sizes up to 3" and flow rates up to 250 GPM (56.8 m3/hr) and can service tanks up to 63" inch diameter.
The cycles can be set for downflow or upflow regeneration, or simply service, backwash and rinse and are the easiest valves to service in the industry. They are simple to configure for use in multiple tank systems, the valves come in different program versions and are controlled by solid state microprocessors with front panel settings and screen display. The valves have a complete line of accessories including stainless steel flow meters, motorized alternating valves, no hard water bypass and system controllers
The SGA Series Ozone/Oxygen Systems are the most powerful and compact ozone systems in their class. Each unit combines a high concentration, air-cooled ozone generator with an onboard oxygen concentrator in an attractive, compact, wall or floor mounted stainless steel housing.
The powerfull SGA Series is easy to operate with a convenient, intuitive control panel. To easily manage the ozone generatin process, it offers:0-100% variable power control, feed gas control, inlet air pressure and reactor back-pressure gauges, power supply feed back reference meter, and LED ozone production indicator.
All SGA Series ozone generators can be controlled by a 0-10vdc signal with the optional Automatic Proportional Control (APC) installed. This option is ideal when automatic and continuous control of ozone output is required for a specific process or application.
A highly efficient, reliable ceramic/titanium reactor cell uses an exclusive Floating Plate Technology™. It is powered by an advanced, high-frequency pulse modulated variable control power supply. Responsive, accurate ozone output control is assured by instantaneous amplitude modulation and proven stability of the Floating Plate Technology™ reactor cell design.
The SGA Series ozone generators are engineered to meet the ozone process requirements found in the most demanding applications, yet with an efficient design that assures minimal maintenance and years of trouble-free operation.
We bring forth for our clients, a wide range of RO housings, manufactured by Wave Cyber, a leader in membrane & FRP Pressure vessels in the world.
Our range of RO housing is manufactured from superior raw material, these RO housings are specially designed to withstand high pressures. FRP material provides resistance to most chemicals and hence can be used in a variety of corrosive environments.Further, these housing are in adherence with the set industrial standards, which makes them most sought after in the markets. These thousands of successful installations of RO housings are the result of stringent quality control mechanisms, advanced technology & cordial service philosophy.
Product Range: RO Housings come with complete head assembly with 20-40% lesser parts. 4" and 8" End port, Side port & Multiport options From 150 psi to 1200 psi upto 8 element.